Great War truck Posted October 30, 2019 Author Share Posted October 30, 2019 I had a rummage around in the garage on Monday and found another box of Peerless parts including some more bonnet catches of which three looked to be in great condition. It is funny, you forget what you have got and forget even more where you left them. Quote Link to comment Share on other sites More sharing options...
Great War truck Posted October 30, 2019 Author Share Posted October 30, 2019 We went looking for front Peerless springs. I am quite happy that we have now searched everywhere and we only have the ones on the complete chassis and this slightly sorry looking pair. Quote Link to comment Share on other sites More sharing options...
Great War truck Posted November 3, 2019 Author Share Posted November 3, 2019 Dad has been keeping himself busy with some more painting. 1 Quote Link to comment Share on other sites More sharing options...
Great War truck Posted November 3, 2019 Author Share Posted November 3, 2019 and even more: 1 Quote Link to comment Share on other sites More sharing options...
Minesweeper Posted November 9, 2019 Share Posted November 9, 2019 These are the front springs - they have been sand blasted to clean them and to make a full examination of their condition easier to assess. You will see that they are in an indifferent condition - heavily rusted, one leaf broken, the leaves have spread and the bronze bushes on one are heavily worn. We have decided to send these to a Springs specialist to look at - repair if possible or to be used as a copy for new ones to be made. Fortunately, the rear springs are in good condition - we have two sets of those but only the one pair of "fronts". 1 Quote Link to comment Share on other sites More sharing options...
gritineye Posted November 22, 2019 Share Posted November 22, 2019 Nice work as usual chaps, I wonder if as much care was taken when refurbishing Peerless lorries back then, when delivery was promised in 14 days. 1 Quote Link to comment Share on other sites More sharing options...
Great War truck Posted November 23, 2019 Author Share Posted November 23, 2019 Wow. £295. What a bargain. The first batch from the end of the war were offered at £400 and they had not been reconditioned. Dad has not been able to find any reusable (or reconditionable!) front shackle pins so has been making them. Still a lot to do though - the caps to be silver soldered on and machined to correct final profile. Feathers to be made and fitted. 1 Quote Link to comment Share on other sites More sharing options...
Great War truck Posted November 24, 2019 Author Share Posted November 24, 2019 Finished. Here are the new ones alongside the originals. 2 Quote Link to comment Share on other sites More sharing options...
Great War truck Posted December 6, 2019 Author Share Posted December 6, 2019 All Shackles, Hooks and Shackle pins - now cleaned or replaced with the exception of the one Shackle that Steve took away to press out the old warn bronze bushes (now done) ready for fitting. Steve will bring that one missing Shackle with him back to Devon when he next comes down for new bronze bushes to be made and pressed in. 2 Quote Link to comment Share on other sites More sharing options...
Great War truck Posted December 9, 2019 Author Share Posted December 9, 2019 Dad has been painting the flywheel: 2 Quote Link to comment Share on other sites More sharing options...
Great War truck Posted December 26, 2019 Author Share Posted December 26, 2019 Now that the Thornycroft has gone, one of the aims for this Christmas was to straighten the Peerless chassis. It was well jammed in behind the FWD so we had to get that out of the way first. Although it is very rarely used I am pleased to report it started on almost the first swing. We then had to move all of the junk that has built up around it and then with an engine hoist controlling the lift we gently dropped it to the floor. We then rearranged the strop on the chassis and moved the Peerless across the floor, brought the FWD back in and then eyed up the chassis. Straightening the chassis - tricky or difficult. What do you think? Quote Link to comment Share on other sites More sharing options...
Tomo.T Posted December 26, 2019 Share Posted December 26, 2019 Looks like a job for a Portapak ? Quote Link to comment Share on other sites More sharing options...
Gordon_M Posted December 26, 2019 Share Posted December 26, 2019 What do you think of losing just enough rivets to get that third crossmember out of the chassis, then straighten and reinforce each chassis rail in turn, then refit the third crossmember? Quote Link to comment Share on other sites More sharing options...
gritineye Posted December 26, 2019 Share Posted December 26, 2019 (edited) Here's how I straightened my not as big as yours chassis, Put the x members back afterwards, using wood to prevent point pressure helps a lot. Like yourselves I usually find most things are possible at home with enough thought. Edited December 26, 2019 by gritineye Quote Link to comment Share on other sites More sharing options...
David Herbert Posted December 26, 2019 Share Posted December 26, 2019 If you make a loop of rope diagonally across each part of the chassis, from one end of a cross member to the opposite end of the next cross member, poke a piece of wood through the middle of the loop and twist the rope by turning the wood, it is possible to exert a huge amount of force. I would expect that a triple loop of 12mm blue polypropylene rope would easily pull the chassis into line. You would probably have to pull two adjacent sections of the chassis in opposite directions at the same time or you will just parallelogram the whole thing but doing it this way is very controllable and is not trying to rip the joints apart but to pull them together so is much safer than a Portapak. David Quote Link to comment Share on other sites More sharing options...
radiomike7 Posted December 26, 2019 Share Posted December 26, 2019 Agree with Gordon and Bernard, the chassis rails are bent not lozenged so remove the crossmember, straighten the rails and refit the crossmember. The rivets will have been stressed and will hold a lot better if hot riveted once the rails are straight. Quote Link to comment Share on other sites More sharing options...
gritineye Posted December 27, 2019 Share Posted December 27, 2019 (edited) A couple of further thoughts, it might be tempting to use heat, but I'd avoid that if possible. Although metal can be straightened using heat, on that size metal unless you have two rosebuds going together to get an even heat and an experienced chap in charge, there's no guarantee that unwanted twisting in an unintended direction won't be the result as it cools. I used a 'floating' beam to pull against as it aligned itself with the chassis as it straightened, then I could move the jack and do a bit more. Pulling against a fixed object would mean straightening two bends at once and might need a lot more force. As the webs and the flanges of the rails will have stretched at slightly different rates, it might mean one side of the chassis will end up ever so slightly longer than the other, but not enough to obsess about IMHO. As Mike says hot riveting will take care of any stretched holes, as long as a the one hole in each that's still round and lines up is riveted first it should be fine. Best to get as much input from a few others as you can, but it shouldn't be as daunting as it appears at first, good luck. Edited December 27, 2019 by gritineye Quote Link to comment Share on other sites More sharing options...
ruxy Posted December 27, 2019 Share Posted December 27, 2019 As and apprentice - I took part in such straightening of bent "solebars" on such as bogie-bolster . These solebar could be UB, RSJ, RSC , RSA and often involved a 'bulb-iron' of some description. It would be done by a pair or two pair of fitters and one or two burners using oxy-propane. The rule was - if they could not do it , then rivets were burned off and it was then a blacksmiths job to straighten . Depending - it could have new material or the lot scrapped. IMHO - this lorry RSC section is far to slight and you would endanger insitu. At the mill after the straightener rolls , this size section would be bundled to abt 5 ton and lifted using a pair of wire strops , it would be very floppy when craned ,but it's memory would straighten. These solebar removed are going to be kinked - but you have a good chance to get very straight again if removed. Truly amazing the quality they got from open-hearth steel 100 years ago , I would say the grade will be a bit better than cooking stuff. Quote Link to comment Share on other sites More sharing options...
Richard Farrant Posted December 27, 2019 Share Posted December 27, 2019 There are modern techniques for straightening chassis' nowadays and I remember when we were rebuilding crash damaged DROPS vehicles during the Bosnia conflict (c.1993), a company from London straightened a chassis by a method whereby it did not even have to be stripped out and it was aligned by laser. This is done cold with hydraulic jigs. Quote Link to comment Share on other sites More sharing options...
ruxy Posted December 28, 2019 Share Posted December 28, 2019 (edited) 6 hours ago, Richard Farrant said: There are modern techniques for straightening chassis' nowadays and I remember when we were rebuilding crash damaged DROPS vehicles during the Bosnia conflict (c.1993), a company from London straightened a chassis by a method whereby it did not even have to be stripped out and it was aligned by laser. This is done cold with hydraulic jigs. Quite true what you describe - certain there must be commercial vehicle versions, I would not say that the days of such as the Celette are obsolete (I believe they hired a hessian sack of the unique attachment points, these were often circular for original factory welding fixtures + gripper pads for sills , boot rear flange & engine/beam front X members - for each model of monocoque) Much was left to up to. hydraulic ram control using laser input against factory alignment data . It is about 20 years since I watched this at a firm at Durham that specialized in car body repairs (often what you would consider a write-off) - that business -I believe was financed by a pool of insurers to do this in-house. ------ For this project , if it were I - I would buy/borrow a heavy bearing press min. 20 tons and probably 30/40 tons better . Set up the 'longitudinals' on press table supporting ends on a pair of DIY trestles made from sleepers, fence-posts, whatever. Then quite simply straighten using the minimum of heat to just the flanges. Edited December 28, 2019 by ruxy spelin Quote Link to comment Share on other sites More sharing options...
Old Bill Posted December 28, 2019 Share Posted December 28, 2019 Hello Chaps. Many thanks for your thoughts and observations which are all much appreciated. As we haven't done anything quite like this before, we thought we would just have a go and see what happens as a learning exercise! First job was to make up a a Jim Crow. I had a rummage in the undergrowth behind the shed and found the remains of the Dennis skid-pack on which the engine had originally been mounted. A brush off and removal of the bolts left me with two two solid pieces of C-section. I spaced these two apart with blocks of wood and mounted the ram from our 10 tonne hydraulic press in the middle. This is the challenge. The chassis is lovely and crisp and unworn but was kinked when they pulled it out from under the house in Salisbury. We want to try to reduce this a bit. We rigged up the beam with a couple of bits of wood to make sure it stayed where we wanted it and then looped some chains around the ends. Install the ram and give it a push. Stand back. This could get exciting! At about 7 tonnes, it sprung noticeably the other way. It didn't look too bad and we moved the beam up and down and had a couple more pushes in other places. The net result is that we have removed the kink but the rails now have a slow curve from end to end giving us an offset in the middle of about an inch. The question now is does this matter? Experience is telling me that the only way for us to get it perfect is to strip the rails from the assembly and bend them individually as has been suggested above. To be quite honest, this would be a real pain and I don't want to do it! There is a long propshaft between the engine and gearbox so the alignment is not an issue so what do you think? I would value some opinions! Steve 1 Quote Link to comment Share on other sites More sharing options...
Down and beyond Posted December 28, 2019 Share Posted December 28, 2019 I would leave it personally but your restoration project is already embarrassing my little sankey trailer one your doing a great job and once it is all back together will never be noticed in my veiw ! Quote Link to comment Share on other sites More sharing options...
gritineye Posted December 28, 2019 Share Posted December 28, 2019 Good job chaps, glad that worked well. Over that length an inch is probably within original build tolerates, I wouldn't worry if it doesn't make any bodywork look wonky. I would check the rivets and give any loose ones a rap with an air hammer before painting. Quote Link to comment Share on other sites More sharing options...
Gordon_M Posted December 28, 2019 Share Posted December 28, 2019 It looks "good enough". but sometimes good enough- isn't. If you weren't intending to use it immediately I'd put it up on its side and load it a little to encourage the curve to come out. Definitely agree with checking the rivets, particularly around that third crossmember where I would have expected some to move. Quote Link to comment Share on other sites More sharing options...
andypugh Posted December 28, 2019 Share Posted December 28, 2019 1 hour ago, Old Bill said: Experience is telling me that the only way for us to get it perfect is to strip the rails from the assembly and bend them individually as has been suggested above. Can you borrow an I-beam as long as the chassis and repeat the process above but anchored at the ends and pushing in the middle, probably with a relatively flexible wooden spreader? (Or, turn the chassis upside down on the floor and use concrete anchors as the fixed points) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.