Rootes75 Posted June 6, 2022 Share Posted June 6, 2022 All the work is looking very good. Its nice to follow this. Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted June 9, 2022 Author Share Posted June 9, 2022 Thankyou both for your kind words. Last weekend i got the small square locker on the near side of the body put together - only 58 wood screws! and also my brother came over and helped put the crane winch on. Richard 5 Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted June 9, 2022 Author Share Posted June 9, 2022 I've been giving some thought to how i'm going to lift the rear body onto the vehicle, and interested in how others have done it. I thought about lifting it with a forklift under each side and reversing the vehicle in under, but think it might be a bit dodgy and i'd have to do all the manouvering rather than watching and guiding it into position. I'd like to get a mobile crane in so it can be hoisted straight down, but not sure where to sling it so as not to damage paintwork. Thought about slinging it round the roller that the jib slides on and round the winch drum. Thoughts? 1 Quote Link to comment Share on other sites More sharing options...
67burwood Posted June 9, 2022 Share Posted June 9, 2022 Do you have extended forks for the fork lift? Would it be possible to support the rear body with slings from the rear and guide it on? Not sure on the counter balance 🤔 Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted June 10, 2022 Author Share Posted June 10, 2022 11 hours ago, 67burwood said: Do you have extended forks for the fork lift? Would it be possible to support the rear body with slings from the rear and guide it on? Not sure on the counter balance 🤔 No i don't have extended forks and I don't think lifting it with one forklift from behind would work anyway. Slinging points are difficult to find now that the floor is bolted down, thats why i thought the jib top roller and the winch drum would be good candidates. If i lift it with a forklift under each side, it will be within about 6 inches of the tips of the forks so not much margin for error. Quote Link to comment Share on other sites More sharing options...
67burwood Posted June 10, 2022 Share Posted June 10, 2022 19 minutes ago, Scammell4199 said: No i don't have extended forks and I don't think lifting it with one forklift from behind would work anyway. Slinging points are difficult to find now that the floor is bolted down, thats why i thought the jib top roller and the winch drum would be good candidates. If i lift it with a forklift under each side, it will be within about 6 inches of the tips of the forks so not much margin for error. Would a telehandler work with slings attached to the jib top roller and winch drum? Or Hiab ? Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted June 15, 2022 Author Share Posted June 15, 2022 I lifted it off with a telehandler as you'll see on the first page of my thread, but that was when it was just the framework so an abundance of slinging points and i wasn't worried about messing up my paint job. Also to get it on without knocking it or the vehicle i like the idea of using a mobile crane because it can hoist straight down whereas with a telehandler of hiab crane you have to use a combination of movements to go straight down. Plus its a fairly tight squeeze getting the front legs down between the main winch and back of the cab. If i can satisfy myself that the jib top roller and winch drum are suitable slinging points i think thats what we'll do. I have a local crane hire company in mind who have a small mobile on a 7.5 tonner chassis so should be fairly cheap, but in the interests of keeping things military has anyone local to yeovil got a foden EKA or a militant? Quote Link to comment Share on other sites More sharing options...
radiomike7 Posted June 15, 2022 Share Posted June 15, 2022 Having the body swinging from a crane will make lining the bolts up a lot easier than having to get it in exactly the right place with a forklift or telehandler. The crane we used to remove the Explorer body had a weight indicator that showed just over 2 tons, the Pioneer one should be slightly lighter due to the manual lifting winch. Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted June 16, 2022 Author Share Posted June 16, 2022 22 hours ago, radiomike7 said: Having the body swinging from a crane will make lining the bolts up a lot easier than having to get it in exactly the right place with a forklift or telehandler. The crane we used to remove the Explorer body had a weight indicator that showed just over 2 tons, the Pioneer one should be slightly lighter due to the manual lifting winch. Yeah thats what i'm thinking. I'd reckoned on about 1.5 tons. It won't have the sliding jib in when its lifted cos we'll be using the roller as a slinging point. Quote Link to comment Share on other sites More sharing options...
70HONEYMONSTER Posted June 19, 2022 Share Posted June 19, 2022 Hi Richard ,See attached photos of how I lifted the back body on.Fitted like a glove without even scraping the paint. 7 Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted June 22, 2022 Author Share Posted June 22, 2022 Nice one thanks. Whats your forward most sling going round? is it just choked round the crane? Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted September 12, 2022 Author Share Posted September 12, 2022 Bit of an update. We're nearly there with the back body. I'm going to leave it until its on the vehicle to install the drop down doors, just so i can make space in the workshop soon as poss. Spent the weekend making up the lids for the lockers. I couldn't find hinges the same as the original or even anything that i could modify to look like the original so made some from scratch. That was a time consuming task. In in the interests to getting the finish line as quickly as possible now that its in sight and problems with my big compressor, i'm getting the last bits of blasting done commercially, and have a batch of small bits for the back body i'm going to drop off this week. I've been put onto a local chap with a Foden EKA, so i'm hoping i can get him to come and lift the body on. 8 Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted October 10, 2022 Author Share Posted October 10, 2022 Me and dad working through some of the last big chunks of blasting yesterday 😀 8 Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted April 25, 2023 Author Share Posted April 25, 2023 Morning all, Its been a while since i updated this. There has been lots of work going on in the background, its all the little jobs that take the time. Windscreen is glazed now just waiting final paint before install. I've got various small fittings in manufacture at the moment. Main focus has been the back body, which we fitted at the weekend in its nearly complete state along with the sliding jib section, with help from Matt Slade and his Foden EKA. We'll finish off the rest of the body in-situ. Very pleased with this progress and nearly looking OMG2024 ready . With the body on i trial fitted the rear mudguards and that showed that the mudguard brackets are bent so they've come off for repairs. I'm still in need of a brake pedal return spring if anyone has one going begging?? Richard 9 Quote Link to comment Share on other sites More sharing options...
Rootes75 Posted April 25, 2023 Share Posted April 25, 2023 Looking superb. Quote Link to comment Share on other sites More sharing options...
Scammell4199 Posted June 28 Author Share Posted June 28 The scammell is largely complete, just a few little things left to do like the engine stop cable, finish the markings, crane rope, painting and fitting some of the kit it will carry. So pressure is on to get last bits done in time for XXX corp in September. We’ve been running it to a few very local events including an interesting vehicle meet every Sunday at a local farm shop and WARAG at westonzoyland airfield, which is where i encountered some problems. I had always felt that the engine sounded a bit harsh but didn’t have anything to compare it to. The wife and i were at WARAG, i just started up for the drive home and couple of old boys came over and said ‘that doesn’t sound quite right for a Gardner’. They proceeded to hold the priming levers back and when no.3 was held, it did sound sweeter and more what i recall it sounding like. I drove home very crestfallen and wondering what i was going to so to sort it out. Anyway, i found a fantastic fuel injection ‘team’ in Martyn and Geoff Pitman at Marine Power Services. They came and made an assessment and concluded on a number of fronts that the injector pump hadn’t been calibrated properly. The following week i took the pump and injectors off and dropped them down to their works, where Martyn and Geoff worked their magic, which they captured in this video. I think its evident they really know their stuff. After which they brought the pump and injectors back to my workshop and helped me re-fit making this video in the process. Safe to say the guy who so called ‘calbrated’ the pump originally made a right gash of it, but its now spot on and runs lovely. I’m getting better at the driving each time i take it out. I’ve still got to adjust the clutch brake and I’m currently driving it with the brake backed right off. Don’t think I’m going to bother with the engine side panels for now, at least until i know I’m not going to have to get at the engine in a hurry and they certainly need to stay off till I sort the engine stop cable. 11 Quote Link to comment Share on other sites More sharing options...
Tamber Posted July 11 Share Posted July 11 Wow, that was quite a ways out. No wonder it was a bit funny on №3! Good to see/hear it's sorted and running more like it should! 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.