gary0003 Posted September 19, 2019 Share Posted September 19, 2019 What should the correct jet sizes etc be for the Type 276 carb on my Royal Enfield please? Thanks. Quote Link to comment Share on other sites More sharing options...
Ron Posted September 20, 2019 Share Posted September 20, 2019 The WD/CO carb spec is :- Model 276AC/1A 15/16" bore, 130 main jet, 106 needle jet, needle position 2nd groove down, throttle valve cutaway 2/4, float-bowl 1A. Ron Quote Link to comment Share on other sites More sharing options...
gary0003 Posted September 20, 2019 Author Share Posted September 20, 2019 Thanks Ron - that explains the troubles I've had! Do you have one of these? Thanks again, Gary. Quote Link to comment Share on other sites More sharing options...
Ron Posted September 20, 2019 Share Posted September 20, 2019 Yes Gary I have a 1943 WD/CO from an RAF contract. I've just stripped the engine to get the crank assembly balanced as there is too much vibration for my liking. But I've also acquired the correct crankcases for my contract, so will rebuild it into those. I also have several other models of WD Royal Enfield's Ron 1 Quote Link to comment Share on other sites More sharing options...
Muttonlancer Posted September 23, 2019 Share Posted September 23, 2019 sorry to butt into your thread Gary but while Ron is thinking about WD/CO's i wanted to ask him if the bracket for the nearside pillion foot peg is the same as the off side as the ones we got from Jan don't seem long enough meaning the peg doesn't fold up very well sticking out at about 45 degrees. regards Ian C. Quote Link to comment Share on other sites More sharing options...
Ron Posted September 24, 2019 Share Posted September 24, 2019 (edited) Hi Ian I don't think Gary will mind if we carry on this thread with more info on the CO. The left side foot rest plate incorporates the field stand, and requires another field stand eye bolt #28416 (or similar) to hang the foot rest out far enough to clear the tool box. Ron Edited September 24, 2019 by Ron Quote Link to comment Share on other sites More sharing options...
Ron Posted September 24, 2019 Share Posted September 24, 2019 (edited) Ian, belay that information. I've just been chatting with Jan and we've discovered that there is some sort of discrepancy in the parts list. It clearly quotes 2 x eye bolt 28416. But these are only 1 3/8" long to the center of the foot rest pivot bolt. I've just measured mine which is about 2 1/8". which is sufficient to clear the tool box. There is no mention in the parts list of this extra long eye bolt or a spacer for the standard eye bolt. Jan can easily rectify this problem and I think will make his own comments. Ron Edited September 24, 2019 by Ron Quote Link to comment Share on other sites More sharing options...
rewdco Posted September 24, 2019 Share Posted September 24, 2019 Looks like the 1" 3/8 bolt was definitely used in 1942 (see 1942 picture below). I guess this was soon noticed and the factory may have fitted longer eye bolts for the footrests on later contracts. But the parts catalogues were never amended, up until the 1945 contracts they give the same number, being the number for the original 1" 3/8 bolt. Quote Link to comment Share on other sites More sharing options...
Muttonlancer Posted September 24, 2019 Share Posted September 24, 2019 Thanks Ron and Jan, I did wonder if I had missed a spacer or something and that photo is exactly as mine is so at the moment I have left the peg off. Quote Link to comment Share on other sites More sharing options...
Ron Posted September 24, 2019 Share Posted September 24, 2019 Ian if you replace the stud with a 3/4" longer one and make a simple 3/4" tube spacer will do it. Ron Quote Link to comment Share on other sites More sharing options...
Muttonlancer Posted September 24, 2019 Share Posted September 24, 2019 That should be easy enough Ron, I thought Jan had made the the brackets from one piece of metal rather then drilling and studding the spacer bit but as you know I know little about engineering but enjoy learning. Quote Link to comment Share on other sites More sharing options...
rewdco Posted September 24, 2019 Share Posted September 24, 2019 Made them with a detachable stud Ian! Just like the originals! 😁 Quote Link to comment Share on other sites More sharing options...
Muttonlancer Posted September 24, 2019 Share Posted September 24, 2019 Thats great Jan, I shall have a go at what Ron suggested, we are really pleased with the two WD/CO bikes we built from the engine and frames we purchased and they ride very well. Quote Link to comment Share on other sites More sharing options...
rewdco Posted September 24, 2019 Share Posted September 24, 2019 Very nice bike Ian! Well done! Quote Link to comment Share on other sites More sharing options...
Chris Hall Posted September 24, 2019 Share Posted September 24, 2019 I don’t think RE ever made a longer stud, all the brackets I owned were the standard length. The pegs just never closed fully. If you look at Rons longer stud you can see it’s circular with a machined flat end. I don’t see RE doing that, more than likely if it was to exist, it would be the same as standard but slightly longer. Quote Link to comment Share on other sites More sharing options...
Ron Posted September 25, 2019 Share Posted September 25, 2019 I think you are right Chris, in all the pictures I have where you can see the left foot rest, the foot rest is either left down or in that halfway position. The pictures are all from around 1942 though. So unless a picture from a later contract proves different......I guess that's how they were. Leaving only a workshop or subsequent owner modification......Like mine! Ron Quote Link to comment Share on other sites More sharing options...
Muttonlancer Posted September 27, 2019 Share Posted September 27, 2019 Right or wrong i have now lengthened the stud and fitted a spacer as i think it looks better and i am less likely to catch my leg on it Quote Link to comment Share on other sites More sharing options...
Ron Posted September 28, 2019 Share Posted September 28, 2019 You're an officer! You can easily order such a field workshop modification...."Sir yes sir"🙂 Ron Quote Link to comment Share on other sites More sharing options...
Bob Marshall Posted September 29, 2019 Share Posted September 29, 2019 Hi Tom, Just looking at your Austin Tilly pictures, and noticed that this is my late fathers Austin Tilly. When we restored it in the mid 70s and my father was a member of the 39/45 Military vehicle group. I was 17 at the time as an apprentice autoelectrian and i made all the wiring looms for it, as per original. It was restored in desert colours with the desert Rat on the front. If you would like any more info please feel free to contact me my phone number is 07836601996 or Home number 01162478636. Thanks Bob Quote Link to comment Share on other sites More sharing options...
Ron Posted September 29, 2019 Share Posted September 29, 2019 Did you mean me Bob? I've had it for over 30 years. I'll phone you. Ron Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.