A.Dady Posted March 26, 2012 Share Posted March 26, 2012 HI chaps I think Ive got a spare jerry can bracket if your still after one, also have a spare air cleaner to if your still after one of them too Andy Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted March 26, 2012 Share Posted March 26, 2012 what other parts you getting rid of mate ?........... Quote Link to comment Share on other sites More sharing options...
Essex5 Posted March 26, 2012 Share Posted March 26, 2012 Very impressed with your doors, Mark. I have 2 NOS front doors and old rear doors - what did you do about the 'reinforcement tube', that goes between them vertically? Did you make it, and how is it fitted? Must do a bit more to mine, it's been stood in the shed for a while! John Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted March 27, 2012 Share Posted March 27, 2012 Very impressed with your doors, Mark.I have 2 NOS front doors and old rear doors - what did you do about the 'reinforcement tube', that goes between them vertically? Did you make it, and how is it fitted? Must do a bit more to mine, it's been stood in the shed for a while! John hi , yes i think it was some metal my dad had in , i will ask him how its fixed when i see him next .the studs etc were mainly taken off old roofs regards Mark .... Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted March 31, 2012 Share Posted March 31, 2012 Not looking too bad !!! ............ Quote Link to comment Share on other sites More sharing options...
A.Dady Posted April 2, 2012 Share Posted April 2, 2012 what other parts you getting rid of mate ?........... Depends, what your after chap? Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted April 11, 2012 Share Posted April 11, 2012 would anyone be able to send me pages from the owners handbook please ? i only need pages 19 and 20 cheers ..........it covers the dash board/little socket etc Quote Link to comment Share on other sites More sharing options...
mungaman Posted April 11, 2012 Share Posted April 11, 2012 depends, what your after chap? im looking for the flat metal grille / light surround and the body clips for the hood ?? Any chance you have anything ?? Mungaman Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted April 11, 2012 Share Posted April 11, 2012 also after the connection blocks that fit under the switch panel please guys. think there is 3 in total....... Quote Link to comment Share on other sites More sharing options...
Essex5 Posted April 11, 2012 Share Posted April 11, 2012 also after the connection blocks that fit under the switch panel please guys. think there is 3 in total....... Yes, there are three fuse-holders in a row on brackets under the switch panel - 6 fuses in each as I remember (without going out to look!) John Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted April 12, 2012 Share Posted April 12, 2012 Yes, there are three fuse-holders in a row on brackets under the switch panel - 6 fuses in each as I remember (without going out to look!) John yes , dad just finished the switch panel , metioned last night our holders have seen better days ........ Quote Link to comment Share on other sites More sharing options...
paulob1 Posted April 19, 2012 Share Posted April 19, 2012 the gearbox in my munga is broken, one of the bearings on the splined shaft to the box has failed completely...its the smaller of the two splined shafts, anyone have a number for this bearing, its a ball bearing unit, must be an equivalent... Quote Link to comment Share on other sites More sharing options...
Essex5 Posted April 19, 2012 Share Posted April 19, 2012 Looking at the parts manual, most of the bearings are roller or needle-roller types, there are few ball-races. The front one on the lay-shaft is listed as 6205, the wider one at the rear of the lay-shaft is listed as 'Angular contact bearing 3304 X'. The main or input shaft appears to have only needle-roller types. The output shaft to the front diff and rear prop has a roller-bearing at the front diff pinion end, and a double roller angular bearing 3306 X at the rear supporting the prop-shaft flange. So the only one which appears to be an actual ball-race type is the 6205 on the front of the lay-shaft. Hope this helps. John Quote Link to comment Share on other sites More sharing options...
A.Dady Posted April 21, 2012 Share Posted April 21, 2012 im looking for the flat metal grille / light surround and the body clips for the hood ?? Any chance you have anything ?? Mungaman what grille,which light surround and which body clips? I more than likely have some. Andy Quote Link to comment Share on other sites More sharing options...
mungaman Posted April 22, 2012 Share Posted April 22, 2012 what grille,which light surround and which body clips? I more than likely have some. Andy andy can you pm me ? Sent you a private message but it wouldnt > send < like to get these parts ! Quote Link to comment Share on other sites More sharing options...
morris c8 fat Posted April 22, 2012 Share Posted April 22, 2012 One with lots of spares on evil bay Item number: 330721017310 Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted April 23, 2012 Share Posted April 23, 2012 these are some of the bits im after mate ............. Quote Link to comment Share on other sites More sharing options...
A.Dady Posted April 28, 2012 Share Posted April 28, 2012 these are some of the bits im after mate ............. Been to my shed today not got any of those parts. sorry chap Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted April 28, 2012 Share Posted April 28, 2012 Been to my shed today not got any of those parts. sorry chap ok mate , any hub caps?........... Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted April 29, 2012 Share Posted April 29, 2012 The back is taking shape . All the dash switches are in , after some fuse boxes now , they go under the dash on the left side...... Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted April 29, 2012 Share Posted April 29, 2012 first pair of cushions done , Very comfy they are too ............ Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted May 3, 2012 Share Posted May 3, 2012 (edited) after 4 frames please guys that go inside the cushions , they are the ones with the springs on . cheers .........:tup::(see passengers seat in pic above) Edited May 3, 2012 by Willyslancs Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted May 5, 2012 Share Posted May 5, 2012 Anyone got an inlet manifold please guys ?.......... Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted May 12, 2012 Share Posted May 12, 2012 Another seat done,1 left to do , still need a manifold please guys .......:tup:: Quote Link to comment Share on other sites More sharing options...
Willyslancs Posted May 18, 2012 Share Posted May 18, 2012 last seat finished now will get pics when around there this weekend............. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.