antarmike Posted November 8, 2009 Share Posted November 8, 2009 I haven,t a clue on this one, I was given it for free by a tool stallholder. Quote Link to comment Share on other sites More sharing options...
fv1609 Posted November 8, 2009 Share Posted November 8, 2009 It seems to have a serated outside, which suggests it is hand held. I imagine the pins would engage a wide nut or flange with many turns & located in an awkward place. The rectangular channel allows an extension piece from a socket set to engage for initial freeing of the component or final tightening? Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 1/2" square drive through the middle and knurled on the OD. Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 Anyone any good at number crunching? Quote Link to comment Share on other sites More sharing options...
fv1609 Posted November 8, 2009 Share Posted November 8, 2009 Face wrench socket used in aircraft? Quote Link to comment Share on other sites More sharing options...
protruck Posted November 8, 2009 Share Posted November 8, 2009 It looks like the core plug remover in the middle of the 8V 92 detroit block. Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 It looks like the core plug remover in the middle of the 8V 92 detroit block. Would that need a torque setting? Quote Link to comment Share on other sites More sharing options...
protruck Posted November 8, 2009 Share Posted November 8, 2009 i think every thing on them is torqued. it just looks familiar. but the old grey matter is not getting any younger and i could be wrong. Clive ................................... protrucksrvices.com Quote Link to comment Share on other sites More sharing options...
protruck Posted November 8, 2009 Share Posted November 8, 2009 looks like a Kent-Moore number. Clive .............................. protruckservices.com Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 If it drives on the pins, what is the function of the 1/2" wide slot that is cut into the face, running into to Square drive? Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 looks like a Kent-Moore number. Clive .............................. protruckservices.com Etched on the other side is "Sec 3" Quote Link to comment Share on other sites More sharing options...
protruck Posted November 8, 2009 Share Posted November 8, 2009 Not too sure mike, its a long time since i've had a blower of a jimmy and can't remember what the top looks like, but i can remember the plug has the two dowled holes in the top, and that you can't get a spanner in the vee. I may be completly barking up the wrong tree. Clive .............................. protruckservices.com Quote Link to comment Share on other sites More sharing options...
fv1609 Posted November 8, 2009 Share Posted November 8, 2009 (edited) Under the tabs it is Air Ministry, sorry MOD(AIR) related. 5120 NSC for hand operated, non-powered tools I suppose you could ring up Platons & ask them what its for? Edited November 8, 2009 by fv1609 Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 I don't know either, as I say I was given it by a guy who had no clue either... Quote Link to comment Share on other sites More sharing options...
Richard Farrant Posted November 8, 2009 Share Posted November 8, 2009 The company, Platon, is into flow control, gas flow, etc. Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 Platons seem to be involved with flow meters, and measuring systems for checking gas and fluid flow rates in laboratory equipment, I don't know.... Quote Link to comment Share on other sites More sharing options...
antarmike Posted November 8, 2009 Author Share Posted November 8, 2009 The company, Platon, is into flow control, gas flow, etc. Snap, you beat me.... Quote Link to comment Share on other sites More sharing options...
protruck Posted November 8, 2009 Share Posted November 8, 2009 looks like im wrong then.:-X Quote Link to comment Share on other sites More sharing options...
gritineye Posted November 8, 2009 Share Posted November 8, 2009 the slot allows a socket extension to be inserted from the side in order to turn it close to a firewall/bulkhead? tighten by hand, torque up with extension? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.