robin craig Posted August 24, 2011 Share Posted August 24, 2011 (edited) Tonight we tackled the last remaining problem in getting a safety (MOT for you UK folks) done prior to the new owner taking delivery of 02DA45. In our province, Ontario, when a vehicle is purchased, prior to it gaining a registration, a safety check is required to be performed and signed off on by a mechanic who holds papers in this province. I feel it is a good rule, the vehicles being held to the standards of the time of manufacture not present day. Anyhow, i'm loosing the plot a bit. With the right steering relay unit loosing oil at a reasonable rate, it was a fail for the safety, so it had to be dealt with. I consulted with a number of people while preparing to tackle it, I would like to thank, Dan Sicotte and Bill Mullholland for their learned advice. The splined shaft that connects to Pitman arm is where the leak was coming from. When we took the arm off the splines fluid poured out and the perished remains of an o ring came off. We approached the problem by tackling two fronts. First, after Bill told us about the retrofit lip seals some of them have which this one did not have, we went the O ring path. After looking at the width of the washers and the width of the bushing surface from which a leak could come from we decided to use two o rings, a smaller one snug to the splines and a larger one outside of that, two circles one inside the other. Then because of how we had seen oil coming out from the splines themselves, we used pipe dope in the splines. The washers were cleaned and a couple replaced and back on with the arm and the castellated nut and a new split pin and then back together at the tie rod below. After at least half an hour there was no sign of oil and the vehicle was rolled back onto some dry floor for a visual in the morning. Quite a simple fix really, not rocket science. Hope this helps someone R Edited October 10, 2011 by robin craig Quote Link to comment Share on other sites More sharing options...
Toolman Posted August 24, 2011 Share Posted August 24, 2011 Thanks for the info. I think mine is leaking too! MT Quote Link to comment Share on other sites More sharing options...
Diana and Jackie Posted August 24, 2011 Share Posted August 24, 2011 Very helpful as ours are leaking both sides and will have to be done sooner or later D&J Tonight we tackled the last remaining problem in getting a safety (MOT for you UK folks) done prior to the new owner taking delivery of 02DA45. In our province, Ontario, when a vehicle is purchased, prior to it gaining a registration, a safety check is required to be performed and signed off on by a mechanic who holds papers in this province. I feel it is a good rule, the vehicles being held to the standards of the time of manufacture not present day. Anyhow, i'm loosing the plot a bit. With the right steering relay unit loosing oil at a reasonable rate, it was a fail for the safety, so it had to be dealt with. I consulted with a number of people while preparing to tackle it, I would like to thank, Dan Sicotte and Bill Mullholland for their learned advice. The splined shaft that connects to Pitman arm is where the leak was coming from. When we took the arm off the splines fluid poured out and the perished remains of an o ring came off. We approached the problem by tackling two fronts. First, after Bill told us about the retrofit lip seals some of them have which this one did not have, we went the O ring path. After loking at the width of the washers and the width of the bushing surface from which a leak could come from we decided to use two o rings, a smaller one snug to the splines and a larger one outside of that, two circles one inside the other. Then because of how we had seen oil coming out from the splines themselves, we used pipe dope in the splines. The washers were cleaned and a couple replaced and back on with the arm and the castellated nut and a new split pin and then back together at the tie rod below. After at least half an hour there was no sign of oil and the vehicle was rolled back onto some dry floor for a visual in the morning. Quite a simple fix really, not rocket science. Hope this helps someone R Quote Link to comment Share on other sites More sharing options...
pigdog Posted October 10, 2011 Share Posted October 10, 2011 Add both mine to the leaky mess list. Whenever I get brave enough to tackle them I will probably be needing help. Thanks for the pic posted. -Chris Quote Link to comment Share on other sites More sharing options...
robin craig Posted October 10, 2011 Author Share Posted October 10, 2011 Glad you folks are getting some mileage out of this fix. My mate Gerry and I are off this coming Saturday to do the other side of said Ferret and to get the sucker going again. R Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.