sirhc

Are you lpoking to sell the job lot to a dealer? Someone like Marcus Glenn might be a good start. Please post photos of the CVRTs! Chris

Hi Mark, Looks really good with the black paint on, hopefully it proves as reliable for you as it was for me. I'm glad it won't spend another summer parked up in the garage. Chris

Floor looking a bit better after some white paint... next job is to bolt it all back together! Chris

Those electrical plugs are American, which suggests its come off a US built vehicle. I agree with Lee, looks like a smoke discharger switch box. Chris

I didn't, thanks to a troublesome coil... hopefully no reoccurance this year! Chris

It sounds to me like crap fuel or bad plugs. Change the plugs, if it's still horrible try fresh fuel straight to the pump from a can. Those fuel tanks are a nightmare, they fill up with sand etc and are a horrible job to clean. Plus, being so big, you can never keep them full enough and they end up half full of water due to condensation. Chris

There are quite a few mistakes in the text, for example they did not fit the Cummins engine to the UK vehicles till the early 2000s.

I think so. I was interested when I first saw it as it has Messiers on it, seems a shame to leave them sitting there not doing anything! Same with the Samson in the other photo. Chris

Not sure where this one is, but found while searching Google images....

Shame about the headlamps though!

Doesn't look like there was much wrong with these! Chris

What you need is an image map, you can make areas of the image a hotspot. Most HTML editors should let you do it.

Some ANR stuff for you Andy! Chris

A 12 way cable from one box to the other and the power cable are all you need for this.

Do you mean a thermal spray process? http://en.wikipedia.org/wiki/Thermal_spray

Richard, I copied that text out of EMER Power S579 Mod Instr no 15... I don't know what it means either! Chris

The engine data plate should say something like J60 Mk100 or Mk101, A or B. The Mk100 was linered, the Mk101 slotted. A was for CVRW, B was for CVRT. Chris

I don't know how many Streakers were built, but this one still exists..

It seems I forgot to post any photos of the painted turret. This was actually done a while ago. We've also restored and fitted all the hatch locks since this was taken, and bolted on quite a few of the brackets etc. Chris

I've not updated this for a while, so thought it would be time for some new photos. I've been a bit busy recently, so progress has been slow. All the bins for the outside are blasted, some are painted, others will wait till it warms up a bit. A lot of internal bits are also cleaned and painted, but we had one big problem to overcome... When we got the vehicle we knew the fuel tank was full, when pushing it onto the low loader a load came out the tank breather. It turned out to be mostly water, with some fuel sat on top. To get it running and driving we were using a jerry can connected straight to the filter, but before we can paint the floor and put it back together we had the small problem of the fuel tank to sort out. I managed to find a decent submersible pump on ebay for £30 so figured it would be worth a shot, with some clear fuel hose and a 220L drum we were able to empty what was in there in about 20 mins. Opening the apature revealed a big mess... This seems to have been caused by the water corroding the pickup pipe and fuel sender unit. Both are U/S and need to be replaced. The pickup pipe I found lying in the sludge at the bottom! The tank was left overnight, which caused most of the water to freeze and could be easily scooped out and the sludge hoovered up. You can see a bit of ice in this photo! The tank needs another hoover after it's dried, by which time I hope to have repaired the pickup pipe. The next job is to paint the floor, I started in the drivers compartment, some etch primer and some white bilge paint makes quite a difference. The whole floor and sides of the hull will get 2 coats before reassembly. In addition to this I finally found a gunners site, so this vehicle is now complete parts wise. I still need another one though if anyone sees one about! Chris

I already had the Marine Clean and just bought the sealant. You'll need to get the tank really clean and fill any large holes first. But yes it works really well. The MW tank I did had sat outside since the 70s with the cap off. I stripped all the paint off the outside, made sure the inside was clean and very dry, then used the sealant on it and it's been fine. Same with the M151 tank. The sealant forms a layer on the inside providing you keep it rotating and ensure it covers everywhere. Chris

Most of them should be in here: http://www.ekmpowershop5.com/ekmps/shops/greenmachines/cvrt-all-variantsmodification-insruction-and-index-1251-p.asp Chris

Richard, Frosts auto restoration do a kit to clean and re-seal a fuel tank. I've done an MW tank and an M151 tank and both were perfect afterwards. http://Http://www.frost.co.uk Chris

I think it was done at base overhaul, all of ours have extra armour, one even has a lot of round plates on the bottom. My Sabre has an extra plate welded on just above the track. Chris