09EA50

I have just rebuilt my pump

The engine was working OK until the fuel pump died,
But now I have another problem, I think I have a stuck rack in the injector pump. I have seen a short blog on this in the past but cannot locate it

I don't know much about injector pumps and could do with a little help.
The fuel pump is now refurbed and working, the Solenoid is refurbed & working, the Stop pedal is UP, and the governor has Oil, Fuel Pack filter, and collector tank filter cleaned, The Fuel emptied and replaced with fresh but it will not start.
Nothing coming out of the injector pump, the rack is in the "off" position (To the LEFT Side) so I assume nothing would come out?

Here is my question -  With the Engine stopped and the Fuel solenoid held open should you be able to move the rack manually by pushing on the end Without turning the engine over and risking the engine running away if the rack sticks open or breaking something else?

Any help is appreciated.

Graham

Link to Fuel Pump rebuild -

https://www.tapatalk.com/groups/wwwfv432couk/fuel-pressure-pump-rebuild-t1826.html

Just realised front Oil seal may be different part, not got it out yet, was hopeing not to pull them untill replacements arrive but front seal may be different (422 & 423 of 2350-T-251-711) so, Stuart if you do know the part No it would be appreciated.

Graham

Also see pages 422 & 423 of 2350-T-251-711 Illustrated parts catalogue (1188 pages).pdf

http://www.fv432apc.com/fv432manuals.html

If you dont have it see pdf below - FV432593 Fuel Pump assembly - 356152332_EMERPOWERP424-1 as posted by Clive

Impeller Blades Delphi 7123-388
Diesel Transfer Pump Liner Delphi 7139-223

I have no used them yet but they look correct and according to a blog on the site (which I connot loacate at the moment) is correct, Will post if I re-find.

Can be orderd direct from Delphi but also -
There are other brands but I went with Delphi as they say "Made in UK"

eBay -

Delphi 7123-388 Transfer Pump Blades Automotive Part For Lucas CAV DPA DPS DPC

DELPHI Diesel Transfer Pump Liner DELPHI 26430445 72423692 7139-223

112 056 025 R21/SC Single Lip Nitrile Rotary Shaft Oil Seal with Garter Spring 9/16x1.1/8/x1/4 Inch, 2 Required, available from https://www.bearing-king.co.uk/bearing/112-056-025-r21-sc-single-lip-nitrile-rotary-shaft-oil-seal-with-garter-spring-9-16x11-8-x1-4-inch/9563

And this appears to be a pump inlet maifold that "looks correct" although it is from China

NEW Fuel Injection Pump FOR FORD 7135-180,7139-223

You may also fine these bloggs interesting on the primary fuel filter which is very expensive ( in 2014 they were about £80, Today £245)-

https://www.tapatalk.com/groups/wwwfv432couk/viewtopic.php?p=16343#p16343

https://www.tapatalk.com/groups/wwwfv432couk/viewtopic.php?p=13194#p13194

Regards

Graham

FV432593 Fuel Pump assembly - 356152332_EMERPOWERP424-1.pdf

Found the Oil seal myself, After cleaning you can read it (funny that)  They are 112 056 025 R21/SC Single Lip Nitrile Rotary Shaft Oil Seal with Garter Spring 9/16x1.1/8/x1/4 Inch available from https://www.bearing-king.co.uk/bearing/112-056-025-r21-sc-single-lip-nitrile-rotary-shaft-oil-seal-with-garter-spring-9-16x11-8-x1-4-inch/9563

Thanks

Hi,

You say "seals and rear bearing were available locally they are standard sizes" it would be very helpful if you could tell us the supplier and if possible;e any part numbers. Also did you get new brushes?

I have mine in bits the seals don't look bad very small amount of leakage, It would be nice the get replacements before I extract them. I have New Pump liner & Impeller blades.

Graham

Thanks for the reply

Hope you service improves.

Would be nice to have but sounds like its not going to help withe rebuild of fuel pump.

Regards

Graham

Thanks to Clive, Wish I'd found this before starting my own refurb of fuel pump.

Is the any useful info in "P 428/1 Pump, fuel pressurizing, No.2 Mk 1. Inspection Standard. Aug. 1976 "