Jump to content
Tomo.T

Another J Type on the way !

Recommended Posts

We have been experimenting with an electrolytic  rust busting device, which has been showing great promise in early trials.

received_548489399231437.thumb.jpeg.6ee226c1fccba2b0b27dc152a6ce4c8d.jpeg

received_2530124883942561.thumb.jpeg.61fe402db2cec5faa092ce0267f7b79f.jpeg

 

Made from good solid (free) scaffold boards with a 1000 gauge plastic liner , the tank contains about 12 gallons of water with 6 cups of soda crystals for the electrolyte. Various anodes have been tested and the best was a length of box section steel, this was connected to the positive terminal of the power source. The negative end connects to the job  in this case the steering column and this forms the cathode. 

20191017_122006.thumb.jpg.896600fd8a1798c8ae44b32bf9054239.jpg

At first results were disappointing , with a small battery charger struggling to provide 2 amps to the rather cold mix. Stan then produced the heavy artillery, a monster starter charger which soon got the party started and the bubbles flowing. We explored the full range of options which included a flat out setting of 24 volts and 28 amps. This was proper motoring and was restricted to short periods of boost when required. Amongst other beneficial effects this began to raise the water temp and we achieved 24 degrees C which was much better for the reaction.

20191017_121845.thumb.jpg.b7265bd2b7df29ecbea7a1a7c5a9b0a5.jpg

received_386628312213238.thumb.jpeg.6600f845c399ef8b3c4aae1d97437f25.jpeg

 

 

 

The results shown here after about 4 hrs show the rust mostly gone and replaced by a black substance which cleans off easily ready for paint. The rust was deposited on the anode which was growing a fine set of  Titannic whiskers. Various modifications are at the planning stage, but initial results are very encouraging. 

received_2437900342930832.thumb.jpeg.4278b28551fd395cbf13a332b52abd67.jpeg

received_574995866372715.thumb.jpeg.0fb746f9c875569c9d90afc14ecdf8a9.jpeg

 

received_2926361267391235.jpeg

  • Like 2

Share this post


Link to post
Share on other sites

Presumably about the same as charging a battery, maybe more on the higher settings ? We found the 24 volt input to be the most effective and did most of it on that with the amps on minimum ( 5 or 6 ) . Advantages over acid include faster progress, no damage to bright areas or brass bits and it does not smell like somethings died in there.

  • Like 2

Share this post


Link to post
Share on other sites

Prep time for rusty bits has improved considerably and we are honing the technique as we gain experience. Good connections to bare metal are important and any loose parts (nuts and bolts etc.) need seperate connections to be included in the process. The brake arm and adjusters were put through the mill and after a light brushing with the rotary whizzer, came up like this.

20191023_170653.thumb.jpg.cc35bc5a0118e31f62823d42579c67c5.jpg

The hidden adjuster screw threads did put up a fight and most of a day was spent freeing them up, but Bonda Prime was duly applied at last orders and the brake rods will now join the queue for paint.

20191023_172511.thumb.jpg.a56a09bf0c3216cfcbe6020e1e01f2b8.jpg

 

The previous batch has now had a 2nd top coat of Service Colour.

20191023_172754.thumb.jpg.f396d457d252e4d6cd3ef5cd039b18ec.jpg

20191023_172635.thumb.jpg.9dc325781b1c7249bf64bd5fc9320530.jpg

  • Like 2

Share this post


Link to post
Share on other sites

I was promoted off the floor today ! Stan has cleared the promised shelf space and I have taken up residence in the stores. Several parts are now ready to be reunited with the chassis, with more on the way. Very satisfactory.

20191025_162546.thumb.jpg.22b526192673384b3121d2dfcef138aa.jpg

The water jacket connector was cleaned up manually a while back, with good results and has been awaiting one of Stan's free moments to build up the missing corner with braze.

20191015_145520.thumb.jpg.bfe7383480444f5dfc2458dd479a9ed0.jpg

20191015_145624.thumb.jpg.bddc1c40aff29b9421cf037e93621868.jpg

It turns out Stan is a bit of a star on the brazing front as well and a new corner was created freehand after carefully preheating job and firebrick to ensure a nice slow cooling down period.

 

 

20191025_164604.thumb.jpg.e1f37ae53fd4609737b416d7650eaae7.jpg

It only remains for me to file the surface flat and re drill the hole and that's another bit ready for paint.

20191025_164219.thumb.jpg.0d313d6a98017213e169d2f3676d0765.jpg

20191025_164906.thumb.jpg.95f49bc791861fedf1c1bc07811758d6.jpg

 

 

Edited by Tomo.T
Remove duff pic

Share this post


Link to post
Share on other sites

Nice work with the brazing. I wonder if MIG brazing would work for that sort of application? 

(It wouldn't be better, but not everyone has access to Acetylene, and the access is reducing steadily) 

I would be tempted to skim the sealing face flat on the lathe, it looks easy to hold for that. 

Edited by andypugh
  • Thanks 1

Share this post


Link to post
Share on other sites

 I'll ask Stan, in the meantime I'm on with the file tomorrow,  I'll post more pics  if I don't cock it up !

 

 

Share this post


Link to post
Share on other sites

Looks like you filled in the entire corner with brass. I have done the same job by locating a piece from a similar flange, cut the corner off and matched the two pieces together to a reasonable degree, then brazed them together.

Are these pieces the water passage between the two cylinder castings? 

Ian

  • Like 1

Share this post


Link to post
Share on other sites

Yes Ian, we recovered the part from the remains of the second engine. Repair is mainly cosmetic.

Share this post


Link to post
Share on other sites

Got somewhat diverted this morning with the rugby ! 🤗 but back on the case this afternoon for some filing. Miserable weather and poor light for the pics, these are the best of them.

20191026_191932.thumb.jpg.360ee1119131023c066e2a6bdd51253d.jpg

The mating surface is pitted and not very flat, so will need facing up and a thicker gasket.

20191026_164727.thumb.jpg.6f276c509986778870fec9ebdbecb0ad.jpg

Otherwise the braze cleaned up well, I clamped and bolted the other faceplate back to back, to drill the hole, it remains to be seen if that was a good idea or not.

20191026_170314.thumb.jpg.91892dd109c0e959ca256777ca32744a.jpg

 

 

  • Like 4

Share this post


Link to post
Share on other sites

Due to a lack of work, I have been able to catch up on a bit of painting. (Anyone requiring proper signwriting or brush painting, please get in touch ! )

I found the sump languishing on the shelf and decided to lavish further attention on it. This ugly duckling will soon re emerge swan like and will hopefully repay my efforts by remaining contenent, once filled with oil .Various other parts are also making progress. 

 

20191029_165729.thumb.jpg.b80a6ef02e03946b0e5e3203de733809.jpg

20191029_172206.thumb.jpg.3246afec765a740866b860fb0441e4c5.jpg

20191030_160043.thumb.jpg.9d1aee8d7f0c8d0912653e94acf0fb7c.jpg

Progress has also occured at the airfield and the project has moved to an independent workshop where I can have free access. This is a major improvement and much appreciated.

20191031_143836.thumb.jpg.960d059fc7843d7af3ce8d1f91ae21c9.jpg

20191031_143948.thumb.jpg.e33bf40c2d195310686d97b2166bccfe.jpg

 

  • Like 2

Share this post


Link to post
Share on other sites

It would be good to see some bits going back on I think. Here is the steering box taking up residence in its new work place. It needed a little persuasion as the holes didnt quite line up, (different parents) but a little file work soon sorted that. However, I am not convinced that the end result is quite vertical and it may need a shim to straighten it up.

20191105_141755.thumb.jpg.99edc39e91373d798b792dec2de3bcc3.jpg

20191105_134911.thumb.jpg.a62e3bbcc08f767503895c2035f76dbc.jpg

The sump has come out nicely. If any one needs one of these, now is the time to scan this one and get a pattern 3D printed. (Just saying.)

20191104_154748.thumb.jpg.941ef50b209e3814172733980879247b.jpg

 

I will just include a couple of 'before' pics20190506_121442.thumb.jpg.e7163996d71fb516e242851875e4090c.jpg of the moonscape I started with.

20190501_153753.thumb.jpg.c35d262c357542fdc2533105b8a93863.jpg

 

Edited by Tomo.T
Duff pic.
  • Like 1

Share this post


Link to post
Share on other sites

sorry I didn't go back and check so if you have already answered this - but how did you alter the moonscape? Looks awesome!

Share this post


Link to post
Share on other sites

Chemical assistance- (Belzona) after a thorough soda blasting, and turd polishing.

Full story page 3

Update page 4

Edited by Tomo.T

Share this post


Link to post
Share on other sites

My long awaited valves have arrived from G&S and will be taken directly to  Paynes at Evesham where they are waiting to finish the cylinders and valve guides.

20191107_103224.thumb.jpg.d1d8f6aabbba32f0fad9d6188a533598.jpg

 

Also back from Rob Foreman ( Mr Solex ) is my MOV 35, newly re jetted and refurbished. This magnificent bronze carb is slightly later than the original, but has many improved features, including butterfly throttle, idle mixture adjustment and a choke. These are also easier to find and a fraction of the price of the early ones. This particular example came from the south of France, where it was previously employed on a vintage Bentley. The enormous main jet it had, would appear to support this assertion.

20191107_105931.thumb.jpg.bf756e87be65809f52a235c03ead801b.jpg

Edited by Tomo.T
Better pic
  • Like 1

Share this post


Link to post
Share on other sites
On 11/6/2019 at 1:00 AM, Tomo.T said:

Chemical assistance- (Belzona) after a thorough soda blasting, and turd polishing.

Full story page 3

Update page 4

off to check - thanks very much!

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...