fesm_ndt Posted December 19, 2016 Share Posted December 19, 2016 Very nice job you are doing :-D Quote Link to comment Share on other sites More sharing options...
goanna Posted December 19, 2016 Share Posted December 19, 2016 Hey Mario You can come down here and restore my CS8 .... Quote Link to comment Share on other sites More sharing options...
David Herbert Posted December 19, 2016 Share Posted December 19, 2016 I like your use of CAD (Cardboard Aided Design) You can't beat modern methods :-D. David Quote Link to comment Share on other sites More sharing options...
Ausprey Posted December 19, 2016 Author Share Posted December 19, 2016 Very nice work, on my C4 there where wedges between the leaf springs and the front axle. These are there to change the front wheel geometry , positive caster . You just can see them on the picture in between the spring and axle . [ATTACH=CONFIG]121608[/ATTACH] thank you for your comments and your help,can you tell me there diamensions and are they spring steel. thx Quote Link to comment Share on other sites More sharing options...
Ausprey Posted December 19, 2016 Author Share Posted December 19, 2016 does any one has 4 front spring U bolds for sale please thx Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 2, 2017 Author Share Posted January 2, 2017 hello all some more work done on the cs8 engine bay brackets , and some parts receved for the morris cs8 , i would like to thank every one who sold parts to us to continue the restoration as many parts were missing . Quote Link to comment Share on other sites More sharing options...
goanna Posted January 3, 2017 Share Posted January 3, 2017 (edited) Mario Where are you finding these parts ? A CS8 king pin kit ! You have more parts than I do . Mike Edited January 3, 2017 by goanna Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 3, 2017 Author Share Posted January 3, 2017 help needed can any one tell me if this tool box belongs to cs8 under the drivers floor board if not can any one identify for what it is, and does any one has a photo of one .it came with the morris cs8. thank you very much for your help. Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 8, 2017 Author Share Posted January 8, 2017 hello all hope every one had nice holidays some work done in engine bay and passinger foot well during the holidays, if any one could give me some information about the tool box in the photes i appriciate it Quote Link to comment Share on other sites More sharing options...
rampant rivet Posted January 8, 2017 Share Posted January 8, 2017 More great work and progress Mario 😁 Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 8, 2017 Author Share Posted January 8, 2017 More great work and progress Mario 😁 Thank you Jeremy for your help you are doing very nice work on the Bedford not even when it was New it was like Your work Quote Link to comment Share on other sites More sharing options...
goanna Posted January 9, 2017 Share Posted January 9, 2017 pic may be of some help Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 9, 2017 Author Share Posted January 9, 2017 pic may be of some help Thanks Mike can I ask dimension and thickness for The 0utside plate from front to rear of the box thx Quote Link to comment Share on other sites More sharing options...
goanna Posted January 9, 2017 Share Posted January 9, 2017 Do you mean this ? Quote Link to comment Share on other sites More sharing options...
goanna Posted January 9, 2017 Share Posted January 9, 2017 more .................. Quote Link to comment Share on other sites More sharing options...
goanna Posted January 9, 2017 Share Posted January 9, 2017 will this ever end Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 9, 2017 Author Share Posted January 9, 2017 more .................. No Mike on the autside opposite to chassis from Front plate of 1/4 thick to rear plate of 5/16 thick Thanks Mike Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 9, 2017 Author Share Posted January 9, 2017 Can any one tell me on cs8 compressed where the battery box should be because between the seats there is the drive for the compressor thx Quote Link to comment Share on other sites More sharing options...
rampant rivet Posted January 9, 2017 Share Posted January 9, 2017 Have you tried contacting Raferk yet I am sure he'll be more than happy to help you, plus he is a good contact for spares. Quote Link to comment Share on other sites More sharing options...
goanna Posted January 10, 2017 Share Posted January 10, 2017 Mario If you want any more dimensions, save the relevant picture and do the editing in 'PAINT' eg note which dimension you need and then email me the picture to me . Mike Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 10, 2017 Author Share Posted January 10, 2017 Have you tried contacting Raferk yet I am sure he'll be more than happy to help you, plus he is a good contact for spares. Yes I send a mail and he send me once but I send again And I heard nothing probably he will be buesy thx jeremy Quote Link to comment Share on other sites More sharing options...
goanna Posted January 10, 2017 Share Posted January 10, 2017 Who or what is raferk . Maybe a ex RAF flight mechanic ? Quote Link to comment Share on other sites More sharing options...
Ivor Ramsden Posted January 10, 2017 Share Posted January 10, 2017 RAFerk is a member on here. Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 11, 2017 Author Share Posted January 11, 2017 HI CAN ANY ONE TELL ME WHITCH HATCH IS FOR THE CS8 1940 (for the distributer cup) from the driver side because i saw 2 different types i am going to put the 2 photos and i need to assemble it .thank you Quote Link to comment Share on other sites More sharing options...
Ausprey Posted January 11, 2017 Author Share Posted January 11, 2017 HI CAN ANY ONE TELL ME WHITCH HATCH IS FOR THE CS8 1940 (for the distributer cup) from the driver sidebecause i saw 2 different types i am going to put the 2 photos and i need to assemble it .thank you And the front drivers side where you rest your feet it Should be wood or steel because I so off both thx Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.