Results 1 to 7 of 7

Thread: Chevrolt M6 Bomb Service Truck

  1. #1
    Join Date
    Mar 2007
    Location
    Ipswich
    Age
    45
    Posts
    136

    Default Chevrolt M6 Bomb Service Truck

    Some of you may remember that this time last year I was offered a friends M6 bomb service truck and M5 tri-cycle bomb trailer, money changed hands and the deal was done. I was very pleased to say the least with my purchase if only the wife felt the same. She thought she was getting a new kitchen!! Below is a picture of the M6 as purchased after removing all the covers and it seeing the light of day for the first time in six years.





    If anyone wonders no I haven't aged in the last year the bloke is David Tuthill who I bought it off.

    Since purchasing the project I have been busy collecting the missing parts that are needed for the vehicle. All the brake cylinders and master cylinder have been resleeved in stainless and rebuilt by Past Parts of Bury. I have stripped down the series one hydrovac which is ready for rebuild once Rex finds the small stop pin that is missing, Rex had the required piston seals for the series one hydrovac on the shelf!

    NOS side door straps were purchased, along with a few bargain eBay purchases such as NOS dash mounted load controller for 5. Adrian Barrell very kindly found a NOS fuel pump rebuild kit and governer, neither of which had even been opened until I got my grubby mits on them.



    Well the time finally arrived last Wednesday to transport the M6 from storage at Debach airfield and transport it to Howards, at Great Finborough to begin the epic restoration. Howard was right on time arriving bang on 8AM, we collectted the trailer on loan courtesy of Richard Taylor. We deceided to remove the rear bomb crane in the interest of saving weight and loaded the M6 ready for the short journey, Howard used every ratchet strap he could find determined to ensure the load arrived safely!

    Here it is in the lean to ready to comemnce stripdown.





    First things first we had a nice cake and a cup of coffee!! Next off with all the front end sheet metal, which is all in quite good condition, it also has the correct lights, front grill and horn (mounted on the fender as with all M6's). Interesttingly all the sheet metal was held on with M8 nuts and bolts!!



    We decided that we had better run the engine and make a decision on what to do with it as it has a frost crack in the block that has been badly welded and still weeps slightly. Once fuel was up a few cup fulls down the carb and away she went. The engine is a 1940's Chevy 235, but not the correct military contract BV1001 engine. I was fortunate enough to purchase two other 235's from eBay last year one of which is also frost cracked but the other is supposed to be a good runing 235 with full pressure oiling rather than splash fed oilling used on early 235's. These engines are currently at Adrians awaiting the move to Howards. Thanks Adrian!!!

    Next the rear bed was removed and then the cab. The wood on the rear bed will be replaced with oak or ash and painted OD, the current wood is mahogany and straight cut rather than tongue and grooved. I am lucky that I was given an original plank off an M6 so can get the new wood machined as per the original plank. The cab is OK condition but has rot at the base of the scuttle and also at the rear of the floor pan. It also looks as though the floor pan may have been replaced at sometime, due to the excessive welding, will know more after blasting.





    Not bad progress for day one!

    A couple of weeks ago when Clive and Tony were over at Jaaps yard they very kindly brought home for me a chassis mounted fuel tank for the M6 (different to a standard Chevy). I was very pleased with it as it had the original mounting frame and straps still on it, along with a fuel sender! It fits perfectly on the chassis with all bolt holes lining up, what a result!

    Next I removed all brake lines, shock absorbers, wiring, rear lights and various other bits and bobs. Next the gearbox was dropped and then the engine removed.



    A few more odds and sods were removed and the chassis was bare! Two days of good work and the chassis and axles are ready for blasting and paint. Over to you Howard!

    WC-51 runing and driving!
    3 x Clark tugs
    very rough Cletrac MG-1 plus two chassis
    Chevrolet M6 and M5 trailer
    Clark CA-1 bulldozer

  2. Advertisement

  3. #2
    Join Date
    Oct 2008
    Location
    Portsmouth, UK
    Posts
    426

    Default Re: Chevrolt M6 Bomb Service Truck

    very nice project you got there, and even nicer workshop. look forward to seeing the progress.
    Barry Ring
    Whitedell Engineering Ltd
    http://www.facebook.com/militaryvehiclerepairs

    Service and repairs for classic cars and military vehicles.

    Morris LRC MK11
    Ford GTB Cargo
    Bedford Scammell OXC

  4. #3
    Join Date
    Jun 2011
    Location
    Forest of Dean Gloucestershire
    Age
    56
    Posts
    1,342

    Default Re: Chevrolt M6 Bomb Service Truck

    Quote Originally Posted by RMS View Post
    very nice project you got there, and even nicer workshop. look forward to seeing the progress.
    yep !.second that on both counts!
    Mitsubishi L200
    All change! Only 1 Series 2 Land Rover now
    and woman of house now happier-ish
    Yamaha XJR1300SP
    Yamaha WR250F
    ....ok...so I accept they're not tanks......but...
    oh yeah...a new addition...
    a 1946 Hudson Commodore 6 Sedan
    1985 ex army Landrover 90
    yes...not a tank either....but..!!....

  5. #4
    Join Date
    Feb 2007
    Location
    Suffolk
    Age
    53
    Posts
    1,138

    Default Re: Chevrolt M6 Bomb Service Truck

    Hello Paul, this is going to be a nice project, I will keep you informed as soon as it goes under the blaster, and will take some pics as I go along.

    Regards Howard

  6. #5
    Join Date
    Mar 2007
    Location
    Ipswich
    Age
    45
    Posts
    136

    Default Re: Chevrolt M6 Bomb Service Truck

    Quote Originally Posted by RMS View Post
    very nice project you got there, and even nicer workshop. look forward to seeing the progress.
    Yes it certainly is a nice project and as for the workshop it is very well equipped and plenty of space, unfortunately it isn't mine it's Howards!!!

    Hence the reason the M6 is here and not at mine. I only have a large double garage which is already filled with a Clark tractor in bits, a Hercules WXLC-3 engine in bits, two Cletrac tracks and the wifes new kitchen awaiting fitting!!

    So what did we find on stripdown, well all transfer case oil seals need replacing as do the axle ones and the shaft hub seals. The steering box will get stripped down and rebuilt as will the gearbox as the selector rails were seized when purchased. I have since freed these off to confirm all gears are there and working, interestingly the gearbox has had a small compressor mounted where the PTO drive would be, a useful addition which will stay.

    New rear engine mounting rubbers will be needed as these are missing, the front engine mount is in good shape through. The steel brake pipes appear to be in good shape and should be reusable after cleaning.

    The main item requiring attention on the chassis is the rear end as it is missing. As this truck was used as a breakdown truck postwar it was at sometime modified and the rear tow pintle mount was cut out. Someone has tried to rebuild it using RSJ and sheet steel, however it is not correct and would buckle if I was to tow the M5 trailer. So this will be another job for Adrian to fabricate the new section and probably rivet it in for me.

    This is what should be at the rear end.





    Over the weekend I did manage to stripdown the windscreen frame and break out the old glass which had badly delaminated. All the nuts and bolts were seized and sheared off, so will need to be replaced. The glass was propably the original and Motor Products Coporation could still be made out on the sealing strip. Now I have a windscreen frame in component form!!

    WC-51 runing and driving!
    3 x Clark tugs
    very rough Cletrac MG-1 plus two chassis
    Chevrolet M6 and M5 trailer
    Clark CA-1 bulldozer

  7. #6
    Join Date
    Mar 2007
    Location
    Ipswich
    Age
    45
    Posts
    136

    Default Chevrolt M6 Bomb Service Truck

    Click image for larger version. 

Name:	ImageUploadedByTapatalk1371588546.834687.jpg 
Views:	9 
Size:	146.0 KB 
ID:	78235

    Well for all you doubters out there that know me progress has been made on this project. Even if not directly by me!

    Howard and I decided to remove the axles so be could blast the chassis and ensure every bit was reached.

    As you can see from the picture the axles have know been refitted the chassis has been blasted and painted.

    Adrian has fabricated a new front bumper and new rear crossmember, so the chassis is now ready for the build up.

    I will update this thread with photos of progress to this point as time allows.
    WC-51 runing and driving!
    3 x Clark tugs
    very rough Cletrac MG-1 plus two chassis
    Chevrolet M6 and M5 trailer
    Clark CA-1 bulldozer

  8. #7
    Join Date
    Feb 2007
    Location
    Suffolk
    Age
    53
    Posts
    1,138

    Default Re: Chevrolt M6 Bomb Service Truck

    Here are a few pics of other parts blasted ready for priming, its good to see the restoration back on track. Howard
    Attached Thumbnails Attached Thumbnails b 009.JPG  

    b 008.JPG  

    b 007.JPG  

    b 006.JPG  


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Now Sold FV 11013 : Truck 10 ton General Service Crane General Purpose 6x4
    By Markheliops in forum Old Classifieds & Wanted ads (Closed for new Threads)
    Replies: 10
    Last Post: 30-06-2012, 21:29
  2. Chevrolet M6 Bomb Service Truck and M5 trailer!!
    By P Marriott in forum American Vehicles
    Replies: 35
    Last Post: 01-10-2010, 22:41
  3. WWII Bomb service Truck's
    By abn deuce in forum American Vehicles
    Replies: 3
    Last Post: 18-04-2009, 15:09
  4. CHEV BOMB SERVICE
    By T corbin in forum American Vehicles
    Replies: 1
    Last Post: 11-04-2007, 06:34
  5. Truck mechanic with own breakdown truck/crane in Worcestershire.
    By MilitantGraham in forum Other Chatter
    Replies: 2
    Last Post: 22-01-2007, 22:10

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Allied Forces