Zero-Five-Two

So, what was up with the Atlas? When I say it doesn't work properly, it's things like the off side stabiliser leg goes down but will not go back up by itself, arm extension goes out, but you have to lean on something to push it back in, and so on. Control levers were well seized in places, which is not really surprising as she has spent most of her life outside. Some of them have been bent, presumably by someone attempting to get the thing to behave by forcing the lever over. Take the lot off, and strip to see what's up Once stripped and cleaned it became apparent that some of the original modification work wasn't all that, and a couple of control rods simply couldn't move enough to open the valves properly. So she has most likely been below par since she was first cut down from the original. With a bit of TLC and adjustment the whole thing now works just as it should. There is a hand throttle on the side of the engine cover to turn the revs up when using the Atlas, but I couldn't get that to behave either. You could have just above tick over, which wasn't enough power, or you had the motor screaming at full revs which is not good for it's health. Solution was to replace it with an auxiliary throttle pedal mounted next to the control levers. Perfect, as you stand there working the levers you can put the revs on when you need them and back to tick over when you don't, Good for fuel economy as well I should think. Soon as word got out that it was all working, the "Can you just" jobs turned up. Well, of course I can, any opportunity to show off. Delivering bags of stone for a neighbour Delivering a lathe at work Had to go in the door and down a flight of steps. No problem, I've just got to learn which lever does what. I put numbers on them, but still get it wrong. More practice required

Haven't done anything with it to be honest. Further inspection showed it to be more secure than I first thought. I've done about 800 miles with her now to various shows and jobs out, and it's all good. I've even removed the surplus radius arm.

Well, profuse apologies all round. Write a restoration blog he said, started well and then.....??? Oh dear sorry an' all that, bit of a gap in the scribble. Last post said off to the Detling show. And here we are with the Timber tractor, looking polished and shiny at the Kent Transport Heritage Show Detling. Except this is 2024 a whole year later on, and I haven't written anything in between. Bit of catching up to do. Back to the Tonka, ambition at the time was to get her fit enough to make the journey to the AEC rally at Newark on the May bank holiday weekend. There was a few late nights and long days, but we made it. Biggest panic was getting her safe and road legal. Brakes and steering the main priority and getting all the lights working. Fitted in a couple of local runs to shakedown any problems and got her over to the workshop for a full service. Last minute crisis of a puncture was not in the plan. Bit nervous driving up to Newark, first big run for her, and for me. She drives totally different to any other Militant I have ever driven, and she does bounce a bit with the Atlas right on the back. But of course it made it, she's a Militant. 180 miles each way, no problem. Caused quite a stir with the viewing public, this picture appeared in several truck mags, with people questioning whether she is a Militant or a Matador with a cab swop. Chuffed to bits it all worked, 2 trucks to the big show, brilliant weekend. Back home and the serious work can get started. First job, the Atlas, It does work, I've seen photos and video of it in action. Just doesn't work very well, investigation required

Haven't looked at this thread for a couple of years. So just been reading up on what I've been missing. Incredible job you are doing there and you have achieved so much. Is that dogged determination, or too stupid to know when to stop? Anyway, absolutely well done, and thanks for writing about it all

Evening all, I'm looking for a temperature sensor for a Militant. Part No. FV60668 I'm told they are the same as fitted to a lot of Military stuff in the fifties and sixties. Anyone able to help? Thanks in advance.

Yes, but the Atlas doesn't work because some fool left a pipe undone and it chucked all it's oil out

Thanks for the replies, gents. I've got 25lts of Ultramax 46. Local plant company reckons that would do, as much the same spec as 32 Just wanted a second opinion or two

Hi all, anybody know the correct hydraulic oil to use in an Atlas crane on a Militant? If my memory is still good we used to use OM33 for most plant hydraulics, back in the day, but what is a civilian equivalent?

Thanks for the replies folks, at least I know what it is now, any ideas of value in it's current condition?

Any body able to shed any light on this little beastie? Helping a friend clear a barn full of tractors and stuff and found this. Has a plate on it showing Douglas, but no other readable information. I'm guessing ex RAF from 1960's

I thought it was longer than 3 years, but then, I am old and get confused easily. You've done a damn fine job with her, mate, well done. What are the local shows you are doing, be nice to come along and have a good look at her?

Few more pictures this evening, then. Another missing part or parts was mirrors, well mirror arms in particular. I know they are Bedford RL arms that were modified by the REME, so I put the word out on here and other forums to see if anybody had a spare set. Couple of weeks ago I was offered a pair of Bedford arms that I could be modify to fit. The seller wanted £100 for the pair. I thought stuff that, £100 for what is essentially a couple of bits of bent tube!! Bit over the top. And then, the penny dropped. Bits of bent tube? If I had a pipe bender, surely I could get some tube and make my own for a lot less than £100. A quick look on the net, lengths of tube, tenner each. Pipe bender on facebook market place for a score. Half an hours work and we have two mirror arms for £40, that's better. Just need a couple of mounting brackets. Bit of flat bar with a tab welded on. Have I got a bit of flat bar? No. But I have got an old window winder in the scrap bucket That'll do. Bit more recycling coming up Two brackets, and two more to come from the other window winder. Job done. With the inside of the cab now in top coat and just the ceiling to paint, it's time to start fitting stuff back in. For some reason the photo makes the paint look pink! Honest it is dark red like the other truck. This was last weekend, and the main electrics are going in here, with the addition of a master switch. I've moved the batteries off the floor and onto the storage tray that fits behind the seat. Timber Tractor ones are in the same place and I've found it very useful having them up there when you want to connect extra stuff like phone charger. I managed to measure and make up a battery clamp, but failed miserably with the link cable. Too long and the terminals are back to front too. Another annoying set back that made things difficult for checking the wiring etc as I was putting it in. Still, every thing else seemed to be OK, but she wouldn't start from the dashboard, and I had to hot wire the starter trigger feed to get her to turn over. She still didn't want to go anyway. As I have had the fuel system in bits it all needed bleeding through and a couple of injectors cracking off to get the air out. Once done she fired up nicely. Far better than the last time I had her going when I drove her onto the farm. No smoke this time, and no knocking from over fuelling, which says the new air filter and the reworked fuel system are doing fine. Batteries are charging, red light on the dash goes out just as it should. The not starting from the dash has been traced to a loose connection, and a new link lead has been made up for the batteries. She also needs a new oil pressure sender unit which should arrive tomorrow, so it's all looking good so far. Got to play with the Timber Tractor this weekend, she's out to the Detling show next week and needs a wash and polish etc

Well overdue another update on the restoration, I must get back into the swing of doing these more often. I have been taking a lot of photos, so there is plenty to see. Work has carried on at a cracking pace, most weekends. Still with an eye to making the AEC Rally at the end of May, but the clock is ticking faster each week, it's going to be a close one. Finished off the doors, with both needing a small section of the outer skin replacing Also, there was the other usual problem, both window winders worn out. Easy fix for these, they are almost identical to those fitted to Morris Minors, and new ones easy to find on the net. After the repairs, fresh coat of paint. I've only done the inside for now, outside will get done when the rest of the exterior resprayed. Fuel filter, engine cover and storage bins got done at the same time While we are talking doors, does anybody know if Forum member Ian43 is still doing M.V. keys? Could do with some for the door locks, but I haven't been able to get hold of him. Solved the air filter problem, with the purchase of a Leyland DAF unit, that is small enough to fit in between the back of the cab and the headboard of the body. Unfortunately it didn't have a rain cap, but I managed to invent one using the bottom of an old oil filter, and an exhaust pipe joining piece. Also had to make a right angle piece to fit through the back of the cab I have had one or two set backs, where things haven't gone to plan. Nothing serious and in some cases quite trivial, but none the less annoying and time consuming. The back window of the cab being one of them. The window behind the passengers seat had been plated over and used as the mounting for the hideous air filter. With the filter gone, plan was to return the window to being a window again complete with glass. The old blanking plate could provide a template for the new glass, using the painted area, less a few millimetres for the rubber seal. That didn't work, new glass was far to big all round to fit in. So I had the daft idea of using the window from the Timber Tractor as a template. Easy enough to get out and put back after, except that your have to raise the jib to be able to open the spare wheel carrier to get to the glass. Big delay, and then I find the two windows are completely different sizes, anyway. I knew there were a few differences between the earlier Park Royal cabs and the later Marshall ones, but never realised the back window was one of them. Still, managed to get the glass cut down, and we now have a full set of windows I couldn't use the blanking plate a second time because it had already moved on to a new career. Making missing parts has been a big part of the work so far, and one of the more important missing bits was the little box that contains the indicator switch, flasher unit and warning lights. Old window panel Cut, fold and stick First paint job didn't go too well, so sand it back and start again Add a couple of water slide transfers, and there you go, all ready to plug and play. Fuel system has been overhauled, and all the dodgy rubber hoses replaced with proper metal pipes. The original filter has been refitted, and a nice modern filter separator added to make sure only clean diesel gets to the engine There's more, but I've run out of time this evening, will continue tomorrow

If you do have a spare plug, John, it would be much appreciated. I have nothing at all just now.

Anybody recognise this plug fitting? It's the temperature sensor for my new Militant and is different from the usual Militant (Plessey type) of plug, not that I have one of those either.. As you can see it has quite a fine screw thread and 2 narrow pins to make the connection. I wasn't sure where to post this. I didn't want to post it as a wanted ad as I'm not sure what I do want. Is it a plug or an adaptor to convert to Plessey that I need. Or maybe a different sensor altogether? Or maybe I am just being stupid. Thanks for looking anyway Can't believe I forgot to put the picture up. Now that is stoopid. Thanks John1950 for the reminder