Jump to content

HWade

Members
  • Posts

    975
  • Joined

  • Last visited

Reputation

10 Good

About HWade

  • Birthday 02/22/1964

Personal Information

  • Location
    Suffolk
  • Interests
    Vintage Tractors,Military Vehicles.
  • Occupation
    Sandblaster / mechanic.Full time restoration work.

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Wanted, a good used fuel tank for dodge D60, not the under cab, but out side chassis rail tank.
  2. HWade

    Wanted.

    Wanted Complete NOS clutch pressure plate for GMC CCKW. Thanks.
  3. Wanted Bedford MW dont mind a restoration project. please pm details.
  4. HWade

    Gear box cckw

    Hi, i am in the process of restoring a GMC, The engine is the gmc 302, bell housing and flywheel same as a cckw. I wanted to use the gearbox from a cckw. The problem i have is there is no speedo drive from the gear box. The truck is only rear axle drive so no transfer box. Question did they ever do a speedo drive from this type of gear box, or is there a 5 speed box out there that would fit. Thanks.
  5. Hello John Many thanks for that, ive not yet done anything yet, still working out the best way to go. Howard
  6. Hello Phil. Thanks thats answered my question. Think I will have a swivel both ends. A bit of fabrication coming on. Thanks
  7. Hello Phil, thanks for that, i do have stands i can alter to use as a test bed. But i am after a rotating stand so i can take the engine apart for inspection and rebuild. Also the best location to fix the stand to the block i would imagine remove the clutch housing and then bolt onto those.
  8. Hello Chaps, I am wanting to fit a 1941 ford V8 engine into a stand, and I am looking for recommendations on engine stands, has anybody used one for a v8 and whats out there. Many Thanks Howard
  9. Thanks, I've seen those.
  10. Wanted 12 volt siren as fitted to jeeps and other MV,s.
  11. GMC CCKW 353 Cargo. The truck is very very solid, steel body with wooden floor in great condition.Split Axles, Early grill, The cab is very solid no rot any where. truck still on 6 volt and on the button. Bar grip tyres all round loads of tread, some small signs of cracking. Inside of cab is mint and unmolested. The paintwork has a nice patina. The truck has stood for a number of years so will need going over. I did change the engine oil and drain the fuel tank and stick 40 ltrs of fresh fuel in it. PM me with interest. or mobile 07545107174
  12. HWade

    WANTED

    Wanted for a Dodge WC51 /52 I require a used canvas set for my truck, i could go out and buy a new one but I am after a used one with a good Patina. Thanks Howard
  13. Hello Peter, thanks for the reply and the information, the truck started its life as a decontamination unit, and i guess thats how the lever is there. The tipper was a post war mod done by a company in Norfolk, the pto on it now has a lever coming straight through the floor. This has certainly cleared up what the pull push lever was for. Ive attached a picture of the truck I have nearly finished restoring.
  14. Hello Peter,With regards to the PTO activation lever, I am restoring a dodge d60, which is fitted with tipping gear, when I got the restoration it had already been taken to pieces. The truck has the same lever as yours but i cant for the life of me see cant see where it connects to on the pump on the gear box. There is another lever on the top of the pump that you turn, would the push pull lever under the dash just have been fitted as a matter of course, or should it be connected some where. Many Thanks Howard.
  15. HWade

    Wanted

    Hello Pete Some thing else i need for the c15 is a clutch fork if you have one please. Many Thanks Howard
×
×
  • Create New...