Jump to content

Old Bill

Members
  • Posts

    1,654
  • Joined

  • Last visited

  • Days Won

    33

Old Bill last won the day on June 23 2023

Old Bill had the most liked content!

Reputation

54 Excellent

1 Follower

About Old Bill

  • Birthday 01/18/1965

Personal Information

  • Location
    Leicestershire
  • Interests
    Military Vehicles, miniature steam locomotives, ships, aeroplanes, anything mechanical.
  • Occupation
    Refuse Collection Vehicle Designer

Recent Profile Visitors

11,272 profile views
  1. We have had this done elsewhere in the past but it is nice to be self-sufficient. I always wondered how it was done and this was a good incentive to find out! Steve πŸ™‚
  2. I had a bit of 40x10 strip in stock here so I thought I would have a trial bend. Difficult to photograph on ones own but I got the end hot with the propane, estimated how much length I would need and had a go. It wasn't actually too bad a guess but I didn't pull it over far enough and the pin picked up in the plates and jammed. After dismantling the lot, pressing the pin out and then easing the holes, I warmed it up again and had another go. I am very pleased with the result although I left it slightly too long to close up completely. I will pick up some steel of the correct section the next time I go southwards and do the job properly. I have also been cleaning up Peerless greasers. Dad did a batch a while back but we need some more. They are of a very distinctive pattern with a central spindle which pushes a piston down, forcing the grease through the hole. Unfortunately, the leather seals had all failed or worn away and needed replacing. Rather than try to make up cup washers and rivet them between plates, I turned up some brass pistons and fitted them with O-rings. The difficult bit was the thread. One cup dismantled completely so I measured the thread as 1/4x20 UNC LH and made them all up. Unfortunately for me, all of the other examples had a different pitch of thread! Beeing Peerless, they seem to be 22tpi which is another non-standard size so I had to make up a 1/4x22 LH tap from a bit of silver steel. It wasn't very good but was just good enough the ease the 20tpi threads already cut and allow me to reassemble the things. Another Peerless googly! We want to fit the radiator tape shortly so I have made up a bifurcated rivet attachment for my mole grips. Seems to work! Dad is still painting planks and getting a bit cheesed off with it all. The next mission will be to assemble the body floor which will give us some more space and allow us to start on the side and end planks. We will be out this year! Steve πŸ™‚
  3. Yes, that was my first thought too!
  4. They will have to be hot as they are 50mm x 10mm thick around a 20mm pin so hefty stuff. I found a nice clip of it on Youtube and copied it from there. Now I have to make it work! Steve
  5. I have painted the linkage and made a couple more rod ends for the throttle linkage. Now I am thinking about the remaining body brackets. To that end, I have treated myself to a new toy: It's use is not obvious but the instructions give some very good ideas and it is quite well thought out. First brackets I have bent are parts of the pick and shovel mountings. I was quite pleased with the result. Much better than beating it in the vice and more consistent as this lorry needs three of each rather than just one. The pick bracket is shorter and more difficult to fit in. However, you can see an extra, smaller hole just behind the pin for a bit of bar. I used that and all was well. I was pleased with these and they are being painted. Unfortunately, I didn't pick up any steel for the pick handle bracket so that will have to await another visit to Devon. The tailboard hinges are more challenging. They are 50x10mm flat, rolled into an eye at one end for the hinge pin. Hand forging these is beyond my blacksmithing skills but in my trawling of Youtube, I found a hinge bending tool. I have therefore made one up. Here is a bit of 10mm strip in place. I have not yet had a chance to try it. We are going to need a bonnet soon so I may have to go back on the drawing board until I can get some more steel. SteveπŸ™‚
  6. Thanks. There is a potential hazard there but a bit of thought mitigates it. Just need to think the job through before starting! Steve
  7. Once the chains were on and the axle positioned, I could try my new brake rods. Pleased to say that theylook satisfactory. Then we spent some time setting up the floor planks for painting. It is a bit of a nuisance when your project is also your workbench! Dad soon had them in primer. He has also painted the underside of the wings. He will do the top in situe. In the mean time, I am thinking about fittings. Painting rope hooks is a pain so I have screwed them down to make life a bit easier. After the hand brake, I thought it time to have a look at the footbrake linkage. I have lubricated all the bits and assembled them into place. I also added a couple of greasers, You may remember us trying to dismantle the link between the pedal and the first rod. Unfortunately, we had to give up in the end and cut it to get the centre casting out. I found the bits and the ends for the main pull rod. The two bits on the right should be six feet apart! I have made up a new rod by screwing an eye onto the end and then silver soldering it as usual. I am concious that this is part of the brakes so I will give it a good pull when we fit it just for reassurance. Then of course, the problem of turning a six foot long piece of rod in the Myford. This was my solution to stop the end whirling. I also ran the lathe fairly slowly and fortunately, all went well. Then to drill out and tap the original eye. And silver solder again. The whole length of the bench! And to finish up, a few new clevis pins. The remaining originals that we have are definitely looking a bit tired now. Throttle linkage and painting next! Steve πŸ™‚
  8. Hi Mike. Yes, just for ease of maintenance. It is so much easier to get the pins out when you can see them and also to knock the link pins through. At the moment, they are relatively clean but it is a grim job when they are covered in greasy filth! Steve
  9. Thanks for the explanation Gordon. It is a bit disheartening to have one's patterns totally destroyed. Anyway, onwards. Father has been exercising the paintbrush with wing brackets, wings and lots of bits of wood. The task is never-ending at this point in the project. I have been focusing on the drive chains. Not too difficult but a lot of repetition involved. I took all of the links apart and went over all of the components with a wire brush. Then it was time for reasssembly. Somehow, all of the links had developed a major interference with the pins so I had to dress them out just a touch. I greased every pin and reassembled the bits, finally inserting new split pins. I did this in small sections as it is a horrible thing to handle. The first chain went quite well but the second had a number of links with broken rollers and was short of links as well. I found another chain of the same pattern but the rollers on that one were very poorly. After another look, I found another chain of a different pattern but with slightly better rollers so I stripped both down to mix and match rollers and links and give me a full chain length. A tedious job! At long last, I had two serviceable chains and a few spare links for the toolbox. We have had much discussion about chain lubricant for which many thanks. In the end, I opted for a spray-on chain lube. I understand that this is a very thin solution which penetrates all of the joints before the solvent evaporates leaving the grease behind. I must say that it actually seems to work. Mind you, the solvent is banana scented so the whole shed smells of bananas at the moment! I put the chains in a drip tray and sprayed them all over. It left them rather sticky with grease. Coupled with the lethality of all of the split pins, I made sure to handle them in thick gloves. The gloves are now sticky as well but I managed to avoid slicing my fingers. We wrapped a bit of rope between the links and Dad pulled up the ends whilst I inserted the last link and pinned it. The chain has a tensioning arrangement whereby the axle is jacked backwards using a large spanner. The locknut is then tightened using an even larger spanner and that is secured by a ring which is bolted to the top surface. Once that is done, there is a pinch bolt to grip the thread. They were certainly determined that it wouldn't work loose! My problem then was to decide how tight the chains should be. I settled on a vertical movement in the slack side of 2" as it looks about right. No doubt time will tell. I celebrated by turning the handle at the front and watching the wheels move at the back. Very satisfying. Now we can make it go, we need to be able to stop it so brakes next! Steve πŸ™‚
  10. Still making some progress albeit slowly. Dad went to the foundry this week to pick up the latest castings. The castings are fine but foundries are notoriously brutal with patterns. Ours is usually OK but this time they were a bit heavy handed. Not quite sure what happened here.... Last time we got together, Dad had cleaned up the radiator stay so we fitted that and then did a trial fit of the rod. That was trimmed to length and is now being painted. It is time we had some brakes so I laid out a set of rigging for the hand brake. It was all a bit beaten up but generally salvageable. The two adjuster clevises were past it and I have made some new ones as detailed earlier. Dad painted them hung between centres on the lathe! I had a nice set of parts ready to assemble. The cam lever is right back as the new linings are much thicker than the worn originals. There is a carrier casting in the middle, held down with 5/16" UNS nuts. Fortunately, Dad had made some a while back. When I got to the front, I could only connect the adjuster on the very last thread. If you look at the thread on the LH rod, you can see that it is very short and I suspect that it has been cut back when the linings got thin rather than replace the linings! As the axle will move backwards when I tighten the chains and I will need even more length, this is no good at all and I had to set to and make a new pair of rods. The rods have an eye forged on the end. They would have been done with a set of dies. I don't have those but thought that I might be able to upset the end enough by hand to fashion them. I lit up my fire pot for the first time in several years and had a go. Sadly, with remarkably little success! It is much harder than it looks and I could really have done with an expert to show me how. Oh well. I have to fabricate them. I am a little concerned about this as they are for part of the brakes. However, the original rods were actually tubes and a 7/16" UNF thread has a core area larger than the section of the tubes. I resorted the screwing them together and silver soldering with a good fillet. The solder ran through the thread so I am confident they will be OK. It is essential that the thread on the other end be straight with the correct pitch as it screws into the turnbuckle which has quite a long thread. To make sure that it came out OK, I screw cut the rods to most of the required depth and then just ran the die over the top to take the last few thou off and give it some form. All is well and we have brake rods. Must break out the primer tin this week. SteveπŸ™‚
  11. You may remember that we have had a pair of front wings made. We have two LH wings with brackets so I have salvaged the brackets. Not quite sure how we ended up with LH wings but they must have come from different vehicles and have different types of bracket. We have decided to use them as they are original parts and we don't think anyone will notice. Dad has done a great job of cleaning them up but they do show some corrosion damage. And at the point just next to the chassis rail. I cut some new mounting plates. And then trimmed out the wastage. Then made a fill-in piece. All of the bits were welded in by a pal. I had a couple of happy hours with the angle grinder tidying them up. I couldn't resist a trial fit. The rh one, I put in the vice and twisted a bit to bring it into line but after that they aligned quite well. They will shortly be heading for the paint shop, the next time Dad gets the primer brush out. Steve πŸ™‚
  12. Hi there! Generally, I don't trouble. My woodworking skills are not accurate enough to notice the difference! I usually add generous machining allowances which is fine for one-offs. In a production environment, the foundry wants to give the customer as little metal as possible and the machinist wants to remove as little as possible. The only place I have really noticed is with the Dennis radiator tanks as they are 30" wide. I did leave myself short there and the ends show signs of the rough casting. I'm blacksmithing today but with little success. I'll report later and ask for some advice! SteveπŸ™‚
  13. A bit more pattern making. These should be the last but time will tell. The Peerless has cast floor panels around the base of the steering column and we are fortunate to have most of one of them. Along with a photo showing the other half, I have enough information to make the patterns. I turned and bored a bit of oak for the column radii. Then put some flat strip through the thicknesser. That was a good investment. I don't use it often but makes some jobs very easy. I cut and glued the strips into place. A trim up with the Dremel and the job was well on the way. The original piece showed some strips around the borders so these were soon cut and glued. The Dremel soon made short work of trimming them up. I then went all round with the sanding drum to put a taper on the flanges. Not very much but, hopefully, enough to allow them to be drawn from the sand. A couple of coats of Bondaprime and we are ready to go! Dad delivered them to the foundry this week. Steve πŸ™‚
  14. Thanks for the curved spoke comments. I had forgotten that but a lot of early traction engines had curved spokes. I just fancied the challenge! The starting handle teeth are machined in a sleeve on the end of the crankshaft and we have that. In the outside of the sleeve is a keyway to locate the fan pulley. I have managed to make the fan with the centre line of its pulley further forward than the original so I have put an extra long boss on the drive pulley to allow it to be mounted forwards as well. It may mean that the starting dog begins to enter the bore of the fan but we will find out shortly. There are so many details to get right! I have found today that my new paint is sticking the backing board to the spokes so I shall have to ease them now. Oh well. Steve
  15. Back on pattern making now! Something we don't have is a fan drive pulley. We took the opportunity to measure the diameter of the Bovington example and with this photo, I could make a pattern. However, we also had a photo of the Banfield one. I rather liked the curved spokes so I though I would try to replicate it. MDF is my normal material of choice but this time I opted for a hardwood plywood. It consists of a flat centre with two rings glued onto it. I am very fortunate to have a wood turning lathe. I don't use it often enough so I am not very good at it but I felt that it would be the tool for the job. I managed to produce a nice clean outside diameter and a radius from the ring to the centre. When I did the Dennis radiator pattern, I acquired a scroll saw to cut out the badge. This was just the ticket to cut between the spokes. The pieces I cut out, I used to make a backing board to help the moulder. They just needed a bit of filler in the holes. A couple of coats of Bondaprime with some wire wool to polish them and we are ready for a trip to the foundry. This shows how I think the backing board will work. The idea is that it provides a centre line for the mould so it doesn't have to be hand cut in the sand. Another outing for Father! Steve πŸ™‚
Γ—
Γ—
  • Create New...